1. PFF85-201G – Front Wishbone Front Bush 30mm Camber Adjustable
PFF85-201G gives +/- 0.5 degrees of camber adjustment. If fitting on Audi TT MK1, S3 and A3 MK1 and Seat Leon & Cupra MK1 it fits earlier models with a 30mm diameter. It fits both the pressed and cast arms on the Leon & Cupra MK1 and A3 MK1 2WD. Please check original bush size. Later cars may use a larger (nonadjustable) 45mm bush PFF3-501.
OEM Part Number: 357407182
OEM Part Number: 191407182
1. PFF85-201 – Front Wishbone Front Bush 30mm
If fitting on Audi TT MK1, S3 and A3 MK1 and Seat Leon & Cupra MK1 it fits earlier models with a 30mm diameter. It fits both the pressed and cast arms on the Leon & Cupra MK1 and A3 MK1 2WD. Please check original bush size. Later cars may use a larger 45mm bush PFF3-501. For an on-car camber adjustable version of this bush please use PFF85-201G.
OEM Part Number: 357407182
OEM Part Number: 191407182
2. PFF85-1202 – Front Arm Rear Bush
For the Skodia Fabia 5J, this bush only fits models with these chassis numbers: F5J 8A502 657 Onward, F5J 8B503 032 Onward, F5J 8K450 961 Onward, F5J 83172 974 Onward.
OEM Part Number: 1J0 407 181 / 1J0 407 181 B = Bush
OEM Part Number: 6R0 407 151 / 6R0 407 152 = Arm
3. PFF85-603-20 – Front Anti Roll Bar Bush 20mm
OEM Part Number: Bar = 6Q0411305AN / 6R0411305B
OEM Part Number: Bush = 6Q0411314R
3. PFF85-603-19 – Front Anti Roll Bar Bush 19mm
OEM Part Number: Bar = 6Q0411305AM
OEM Part Number: Bush = 6Q0411314Q
3. PFF85-603-18 – Front Anti Roll Bar Bush 18mm
Please check anti-roll bar diameter before ordering.
OEM Part Number: Bar = 8Z0411305M
OEM Part Number: Bush = 6Q0411314P
4. PFR85-610 – Rear Beam Mounting Bush
Fits 2WD models only. PFR85-415 has been superseded with PFR85-610.
OEM Part Number: 1J0501541B / 1J0501541C / 1J0501541D
OEM Part Number: 6R0501541A / 6R0501541B / 6R0501541C
OEM Part Number: 6Q0501541E / 6Q0 501 541 E
11. PFF85-431W – Front Strut Top Mount Bush Washer
PFF85-431W Front Strut Top Spacer (as normally supplied with PFF85-431 and now available separately) is a simple and cost-effective interim solution that fits and works with the OE Strut Top Cap to fill the gap and prevents binding up on the PU Spacer as the suspension turns.
Fitting couldn’t be easier either. Simply remove the existing Strut Top Cap from the car, separate the rubber ring from it, press the Cap into our Spacer and then refit it!
NB: fitting this part is only recommended if the installed Top Mount is in good condition and there is a gap of at least 12mm between the top cap and body. If the OE mount has collapsed, you will need to replace the entire mount with PFF85-430 or PFF85-431.
OEM Part Number: 1J0412331C
11. PFF85-431 – Front Strut Top Mount Bush -10mm
This part has been designed to reduce the ride height by 10mm when fitted as it allows the strut to sit higher into the body of the top mount. It is supplied with a new top cap spacer made using our 95A durometer material, meaning no more modifying of original parts. For standard ride height top mounts, please use PFF85-430.
OEM Part Number: 1J0412331C
11. PFF85-430 – Front Strut Top Mount Bush
OEM Part Number: 1J0412331C
20. PFF85-620P – Lower Engine Mount Large Bush (Tuned/Track)
PFF85-620P uses our Purple 80A durometer material and is suitable for significantly tuned cars or those used on track. Fitting this engine mount bush to 1.4 TDI 3 cylinders is not advisable. A small increase in NVH, usually at idle, should be expected when stiffening the connecting mount between the engine/transmission and chassis. The harder the material used, the greater the NVH transmitted.
OEM Part Number: 6Q0199851AA / 6Q0199851AC
OEM Part Number: 6Q0199851AP / 6Q0199851AT
OEM Part Number: 8Z0199851H
20. PFF85-620 – Lower Engine Mount Large Bush (Std Petrol)
PFF85-620 is made using our Yellow 70A durometer material and is suitable for standard petrol models or mildly tuned diesel models. For track/tuned models use PFF85-620P. Fitting this engine mount bush to 1.4 TDI 3 cylinders is not advisable. A small increase in NVH, usually at idle, should be expected when stiffening the connecting mount between the engine/transmission and chassis. The harder the material used, the greater the NVH transmitted.
OEM Part Number: 6Q0199851AA / 6Q0199851AC
OEM Part Number: 6Q0199851AP / 6Q0199851AT
OEM Part Number: 8Z0199851H
20. PFF85-620R – Lower Engine Mount Large Bush (Std Diesel)
PFF85-620R is made using our Red 65A durometer material and is suitable for standard diesel vehicles only. For tuned diesel vehicles or petrol models use PFF85-620. For track/heavily tuned models use PFF85-620P. Fitting this engine mount bush to 1.4 TDI 3 cylinders is not advisable. A small increase in NVH, usually at idle, should be expected when stiffening the connecting mount between the engine/transmission and chassis. The harder the material used, the greater the NVH transmitted.
OEM Part Number: 6Q0199851AA / 6Q0199851AC
OEM Part Number: 6Q0199851AP / 6Q0199851AT
OEM Part Number: 8Z0199851H
33. PFF85-633 – Steering Rack Mounting Bush
The OE rubber steering rack mounting bush that secures the rack position is one of those that commonly softens causing vague steering often followed by a pulling feeling on the road, and a less than enjoyable driving experience. PFF85-633 Steering Rack Mounting Bush is a cheap fit-and-forget solution, improving steering response and bringing back a factory-fresh feel. Fits Polo MK3 up to 2013, fits Ibiza MK4 up to 2015 and will not fit solidly mounted racks.
OEM Part Number: 6Q0419884 / 6Q0 419 884
OEM Part Number: 6Q0423844B / 6Q0 423 844 B
OEM Part Number: 6Q0423884B / 6Q0 423 884 B
EXH023 – Exhaust Mount
OEM Part Number: 712770470 / 1756516020
OEM Part Number: 1H0253147B / 1H0253147C / 20650D0101
OEM Part Number: 255047 / 17565-28010
